G05TDF (PDF version)
G05 Chapter Contents
G05 Chapter Introduction
NAG Library Manual

NAG Library Routine Document

G05TDF

Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.

+ Contents

    1  Purpose
    7  Accuracy

1  Purpose

G05TDF generates a vector of pseudorandom integers from a discrete distribution with a given PDF (probability density function) or CDF (cumulative distribution function) p.

2  Specification

SUBROUTINE G05TDF ( MODE, N, P, NP, IP1, ITYPE, R, LR, STATE, X, IFAIL)
INTEGER  MODE, N, NP, IP1, ITYPE, LR, STATE(*), X(N), IFAIL
REAL (KIND=nag_wp)  P(NP), R(LR)

3  Description

G05TDF generates a sequence of n integers xi, from a discrete distribution defined by information supplied in P. This may either be the PDF or CDF of the distribution. A reference vector is first set up to contain the CDF of the distribution in its higher elements, followed by an index.
Setting up the reference vector and subsequent generation of variates can each be performed by separate calls to G05TDF or may be combined in a single call.
One of the initialization routines G05KFF (for a repeatable sequence if computed sequentially) or G05KGF (for a non-repeatable sequence) must be called prior to the first call to G05TDF.

4  References

Kendall M G and Stuart A (1969) The Advanced Theory of Statistics (Volume 1) (3rd Edition) Griffin
Knuth D E (1981) The Art of Computer Programming (Volume 2) (2nd Edition) Addison–Wesley

5  Parameters

1:     MODE – INTEGERInput
On entry: a code for selecting the operation to be performed by the routine.
MODE=0
Set up reference vector only.
MODE=1
Generate variates using reference vector set up in a prior call to G05TDF.
MODE=2
Set up reference vector and generate variates.
MODE=3
Generate variates without using the reference vector.
Constraint: MODE=0, 1, 2 or 3.
2:     N – INTEGERInput
On entry: n, the number of pseudorandom numbers to be generated.
Constraint: N0.
3:     P(NP) – REAL (KIND=nag_wp) arrayInput
On entry: the PDF or CDF of the distribution.
Constraints:
  • 0.0Pi1.0, for i=1,2,,NP;
  • if ITYPE=1, i=1 NP Pi=1.0;
  • if ITYPE=2, Pi<Pj, ​i<j​ and ​PNP=1.0.
4:     NP – INTEGERInput
On entry: the number of values supplied in P defining the PDF or CDF of the discrete distribution.
Constraint: NP>0.
5:     IP1 – INTEGERInput
On entry: the value of the variate, a whole number, to which the probability in P1 corresponds.
6:     ITYPE – INTEGERInput
On entry: indicates the type of information contained in P.
ITYPE=1
P contains a probability distribution function (PDF).
ITYPE=2
P contains a cumulative distribution function (CDF).
Constraint: ITYPE=1 or 2.
7:     R(LR) – REAL (KIND=nag_wp) arrayCommunication Array
On entry: if MODE=1, the reference vector from the previous call to G05TDF.
On exit: the reference vector.
8:     LR – INTEGERInput
On entry: the dimension of the array R as declared in the (sub)program from which G05TDF is called.
Suggested values:
  • if MODE3, LR=10+1.4×NP approximately (for optimum efficiency in generating variates);
  • otherwise LR=1.
Constraints:
  • if MODE=0 or 2, LRNP+8;
  • if MODE=1, LR should remain unchanged from the previous call to G05TDF.
9:     STATE(*) – INTEGER arrayCommunication Array
Note: the actual argument supplied must be the array STATE supplied to the initialization routines G05KFF or G05KGF.
On entry: contains information on the selected base generator and its current state.
On exit: contains updated information on the state of the generator.
10:   X(N) – INTEGER arrayOutput
On exit: contains n pseudorandom numbers from the specified discrete distribution.
11:   IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
IFAIL=1
On entry, MODE0, 1 or 2.
IFAIL=2
On entry, N<0.
IFAIL=3
With ITYPE=1, Pj<0 for at least one value of j.
With ITYPE=1, the sum of Pj, for j=1,2,,NP, does not equal 1.
With ITYPE=2, the values of Pj are not all in non-descending order.
IFAIL=4
On entry, NP<1.
IFAIL=6
On entry, ITYPE1 or 2.
IFAIL=7
The value of NP, ITYPE or IP1 is not the same as when R was set up in a previous call to G05TDF with MODE=0 or 2.
On entry, the R vector was not initialized correctly, or has been corrupted.
IFAIL=8
On entry, LR is too small when MODE=0 or 2.
IFAIL=9
On entry,STATE vector was not initialized or has been corrupted.

7  Accuracy

Not applicable.

8  Further Comments

None.

9  Example

This example prints 20 pseudorandom variates from a discrete distribution whose PDF, p, is defined as follows:
n p -5 0.01 -4 0.02 -3 0.04 -2 0.08 -1 0.20 -0 0.30 -1 0.20 -2 0.08 -3 0.04 -4 0.02 -5 0.01
The reference vector is set up and and the variates are generated by a single call to G05TDF, after initialization by G05KFF.

9.1  Program Text

Program Text (g05tdfe.f90)

9.2  Program Data

Program Data (g05tdfe.d)

9.3  Program Results

Program Results (g05tdfe.r)


G05TDF (PDF version)
G05 Chapter Contents
G05 Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2012