S09AAF (PDF version)
S Chapter Contents
S Chapter Introduction
NAG Library Manual

NAG Library Routine Document

S09AAF

Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.

 Contents

    1  Purpose
    7  Accuracy

1  Purpose

S09AAF returns the value of the inverse circular sine, arcsinx, via the function name. The value is in the principal range -π/2,π/2.

2  Specification

FUNCTION S09AAF ( X, IFAIL)
REAL (KIND=nag_wp) S09AAF
INTEGER  IFAIL
REAL (KIND=nag_wp)  X

3  Description

S09AAF calculates an approximate value for the inverse circular sine, arcsinx. It is based on the Chebyshev expansion
arcsinx=x×yx=xr=0arTrt  
where - 12x 12  and t=4x2-1.
For x2 12,  arcsinx=x×yx.
For 12<x21,  arcsinx=signx π2-arcsin1-x2 .
For x2>1,  arcsinx is undefined and the routine fails.

4  References

Abramowitz M and Stegun I A (1972) Handbook of Mathematical Functions (3rd Edition) Dover Publications

5  Parameters

1:     X – REAL (KIND=nag_wp)Input
On entry: the argument x of the function.
Constraint: X1.0.
2:     IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
IFAIL=1
The routine has been called with an argument greater than 1.0 in absolute value; arcsinx is undefined and the routine returns zero.
IFAIL=-99
An unexpected error has been triggered by this routine. Please contact NAG.
See Section 3.8 in the Essential Introduction for further information.
IFAIL=-399
Your licence key may have expired or may not have been installed correctly.
See Section 3.7 in the Essential Introduction for further information.
IFAIL=-999
Dynamic memory allocation failed.
See Section 3.6 in the Essential Introduction for further information.

7  Accuracy

If δ and ε are the relative errors in the argument and result, respectively, then in principle
ε x arcsinx 1-x2 ×δ .  
That is, a relative error in the argument x is amplified by at least a factor xarcsinx1-x2  in the result.
The equality should hold if δ is greater than the machine precision (δ is a result of data errors etc.) but if δ is produced simply by round-off error in the machine it is possible that rounding in internal calculations may lose an extra figure in the result.
This factor stays close to one except near x=1 where its behaviour is shown in the following graph.
Figure 1
Figure 1
For x close to unity, 1-xδ, the above analysis is no longer applicable owing to the fact that both argument and result are subject to finite bounds, (x1 and arcsinx12π). In this region εδ; that is the result will have approximately half as many correct significant figures as the argument.
For x=1 the result will be correct to full machine precision.

8  Parallelism and Performance

Not applicable.

9  Further Comments

None.

10  Example

This example reads values of the argument x from a file, evaluates the function at each value of x and prints the results.

10.1  Program Text

Program Text (s09aafe.f90)

10.2  Program Data

Program Data (s09aafe.d)

10.3  Program Results

Program Results (s09aafe.r)


S09AAF (PDF version)
S Chapter Contents
S Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2015