S14BAF (PDF version)
S Chapter Contents
S Chapter Introduction
NAG Library Manual

NAG Library Routine Document

S14BAF

Note:  before using this routine, please read the Users' Note for your implementation to check the interpretation of bold italicised terms and other implementation-dependent details.

 Contents

    1  Purpose
    7  Accuracy

1  Purpose

S14BAF computes values for the incomplete gamma functions Pa,x and Qa,x.

2  Specification

SUBROUTINE S14BAF ( A, X, TOL, P, Q, IFAIL)
INTEGER  IFAIL
REAL (KIND=nag_wp)  A, X, TOL, P, Q

3  Description

S14BAF evaluates the incomplete gamma functions in the normalized form
Pa,x=1Γa 0xta-1e-tdt,  
Qa,x=1Γ a xta- 1e-t dt,  
with x0 and a>0, to a user-specified accuracy. With this normalization, Pa,x+Qa,x=1.
Several methods are used to evaluate the functions depending on the arguments a and x, the methods including Taylor expansion for Pa,x, Legendre's continued fraction for Qa,x, and power series for Qa,x. When both a and x are large, and ax, the uniform asymptotic expansion of Temme (1987) is employed for greater efficiency – specifically, this expansion is used when a20 and 0.7ax1.4a.
Once either P or Q is computed, the other is obtained by subtraction from 1. In order to avoid loss of relative precision in this subtraction, the smaller of P and Q is computed first.
This routine is derived from the subroutine GAM in Gautschi (1979b).

4  References

Gautschi W (1979a) A computational procedure for incomplete gamma functions ACM Trans. Math. Software 5 466–481
Gautschi W (1979b) Algorithm 542: Incomplete gamma functions ACM Trans. Math. Software 5 482–489
Temme N M (1987) On the computation of the incomplete gamma functions for large values of the parameters Algorithms for Approximation (eds J C Mason and M G Cox) Oxford University Press

5  Parameters

1:     A – REAL (KIND=nag_wp)Input
On entry: the argument a of the functions.
Constraint: A>0.0.
2:     X – REAL (KIND=nag_wp)Input
On entry: the argument x of the functions.
Constraint: X0.0.
3:     TOL – REAL (KIND=nag_wp)Input
On entry: the relative accuracy required by you in the results. If S14BAF is entered with TOL greater than 1.0 or less than machine precision, then the value of machine precision is used instead.
4:     P – REAL (KIND=nag_wp)Output
5:     Q – REAL (KIND=nag_wp)Output
On exit: the values of the functions Pa,x and Qa,x respectively.
6:     IFAIL – INTEGERInput/Output
On entry: IFAIL must be set to 0, -1​ or ​1. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.
For environments where it might be inappropriate to halt program execution when an error is detected, the value -1​ or ​1 is recommended. If the output of error messages is undesirable, then the value 1 is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is 0. When the value -1​ or ​1 is used it is essential to test the value of IFAIL on exit.
On exit: IFAIL=0 unless the routine detects an error or a warning has been flagged (see Section 6).

6  Error Indicators and Warnings

If on entry IFAIL=0 or -1, explanatory error messages are output on the current error message unit (as defined by X04AAF).
Errors or warnings detected by the routine:
IFAIL=1
On entry,A0.0.
IFAIL=2
On entry,X<0.0.
IFAIL=3
Convergence of the Taylor series or Legendre continued fraction fails within 600 iterations. This error is extremely unlikely to occur; if it does, contact NAG.
IFAIL=-99
An unexpected error has been triggered by this routine. Please contact NAG.
See Section 3.8 in the Essential Introduction for further information.
IFAIL=-399
Your licence key may have expired or may not have been installed correctly.
See Section 3.7 in the Essential Introduction for further information.
IFAIL=-999
Dynamic memory allocation failed.
See Section 3.6 in the Essential Introduction for further information.

7  Accuracy

There are rare occasions when the relative accuracy attained is somewhat less than that specified by parameter TOL. However, the error should never exceed more than one or two decimal places. Note also that there is a limit of 18 decimal places on the achievable accuracy, because constants in the routine are given to this precision.

8  Parallelism and Performance

Not applicable.

9  Further Comments

The time taken for a call of S14BAF depends on the precision requested through TOL, and also varies slightly with the input arguments a and x.

10  Example

This example reads values of the argument a and x from a file, evaluates the function and prints the results.

10.1  Program Text

Program Text (s14bafe.f90)

10.2  Program Data

Program Data (s14bafe.d)

10.3  Program Results

Program Results (s14bafe.r)

GnuplotProduced by GNUPLOT 4.6 patchlevel 3 a x 0 0.2 0.4 0.6 0.8 1 Example Program Incomplete Gamma Functions gnuplot_plot_1 P(a,x) gnuplot_plot_2 Q(a,x) 0 5 10 15 20 0 5 10 15 20

S14BAF (PDF version)
S Chapter Contents
S Chapter Introduction
NAG Library Manual

© The Numerical Algorithms Group Ltd, Oxford, UK. 2015